The SkyTrak 6034 telehandler dashboard provides critical alerts for engine, transmission, and hydraulic systems to ensure safe operation. This page explains each warning light, color coding, and recommended actions specific to this model.
SkyTrak 6034 Warning Light Symbols
| Symbol | Name | Color | What it means | What to do |
|---|---|---|---|---|
| Master Warning (Stop) | RED | Illuminates when a critical fault is detected in the engine, transmission, or safety systems, requiring immediate shutdown on the SkyTrak 6034. | Stop the machine safely, turn off the engine, and consult the fault code display or operator manual. | |
| Master Caution | AMBER | Activates for non-critical system warnings that still need prompt attention, such as low fluid levels or minor sensor faults on the SkyTrak 6034. | Check the warning message on the display and address the underlying issue before continuing operation. | |
| Check Engine (MIL) | AMBER | Lights when the engine control module detects a malfunction in the emission system or engine components, common on SkyTrak 6034 diesel engines. | Reduce load and operate at low RPM; have the engine diagnosed by a dealer as soon as possible. | |
| Engine Oil Pressure | RED | Indicates dangerously low engine oil pressure, which can cause severe engine damage on the SkyTrak 6034 if ignored. | Shut down immediately and check oil level; if full, do not restart and call for service. | |
| Battery / Charging | RED | Signals that the alternator is not charging the battery or the voltage is out of range on the SkyTrak 6034. | Check battery connections and alternator belt; replace or charge battery as needed. | |
| Coolant Temperature | RED | Engine coolant temperature has exceeded the safe limit, risking overheating on the SkyTrak 6034. | Stop the engine, let it cool, and inspect coolant level and radiator for blockages. | |
| Transmission Temp | RED | Transmission fluid temperature is too high, which can damage the transmission in the SkyTrak 6034. | Reduce load and allow transmission to cool; if persistent, check fluid level and cooler. | |
| Brake System | RED | Indicates a fault in the braking system, such as low brake fluid or a brake circuit failure on the SkyTrak 6034. | Stop the machine immediately and do not operate until brakes are inspected. | |
| Parking Brake | AMBER | Lights when the parking brake is engaged or if there is a fault in the parking brake system on the SkyTrak 6034. | Release the parking brake before moving; if light stays on, service the brake system. | |
| Glow Plug / Preheat | AMBER | Illuminates during engine preheat on the SkyTrak 6034; indicates glow plugs are active for cold starts. | Wait for the light to turn off before cranking the engine. | |
| Low Fuel | AMBER | Warns that the fuel level in the SkyTrak 6034 is low and refueling is needed soon. | Refuel with clean diesel to avoid air in the system. | |
| High Beam | BLUE | Indicates the headlights are set to high beam on the SkyTrak 6034. | Dim the headlights when approaching other machines or personnel. | |
| Hydraulic System | RED | Alerts to a hydraulic system fault, such as low pressure or overheating, crucial for lift and steering on the SkyTrak 6034. | Stop all hydraulic functions and inspect fluid level and filters. | |
| Fasten Seat Belt | AMBER | Reminds the operator to fasten the seatbelt before operating the SkyTrak 6034. | Fasten the seatbelt immediately. | |
| Service / Hour Meter | GREEN | Displays total operating hours and may flash when scheduled maintenance is due on the SkyTrak 6034. | Refer to the maintenance schedule and perform required service at the indicated hour. | |
| Work Lights | GREEN | Shows that the work lights are turned on for better visibility on the SkyTrak 6034. | Turn off when not needed to conserve battery. | |
| Beacon / Rotating Light | GREEN | Indicates the rotating beacon is active, required for high-visibility operations on the SkyTrak 6034. | Ensure beacon is operating when working near other equipment. | |
| Overload / Capacity | RED | Warns that the load on the SkyTrak 6034 exceeds rated capacity, risking tip-over or structural damage. | Immediately lower the load and redistribute or reduce weight. | |
| Low Oil Level | AMBER | Engine oil level is below the minimum mark on the SkyTrak 6034. | Add oil of the recommended viscosity to the proper level. | |
| Brake Fluid Level | RED | Brake fluid level is low, which can cause brake failure on the SkyTrak 6034. | Check reservoir and top off with DOT 4 brake fluid; inspect for leaks. | |
| Door Open | AMBER | Indicates the operator door or cab door is not fully closed on the SkyTrak 6034. | Close and latch the door securely before moving. |
21 symbols shown. Icons follow ISO 2575 dashboard standards; exact graphics vary by model year.
Most Important Warning Lights
Engine Overheating
Common causes
- Low coolant level
- Radiator blockage
- Faulty thermostat
What to do
Stop the engine on your SkyTrak 6034, allow it to cool, then check coolant level and clean the radiator fins. If the problem persists, replace the thermostat.
Transmission Overheating
Common causes
- Low transmission fluid
- Clogged cooler
- Excessive load
What to do
Reduce load immediately on the SkyTrak 6034, check transmission fluid level, and clean the cooler core; if the light stays on, have the system serviced.
Hydraulic System Failure
Common causes
- Low hydraulic oil
- Clogged filter
- Pump damage
What to do
Stop all lift operations on the SkyTrak 6034, check hydraulic oil level and replace the filter; if still no pressure, call a technician.
Brake System Malfunction
Common causes
- Low brake fluid
- Worn brake pads
- Air in brake lines
What to do
Park the SkyTrak 6034 on level ground, check brake fluid level and bleed the brakes if spongy; replace pads if worn.
Engine Low Oil Pressure
Common causes
- Low oil level
- Worn oil pump
- Clogged oil filter
What to do
Shut down the SkyTrak 6034 engine immediately, check oil level and add if needed; if the light stays off after restart, replace oil filter and pump if necessary.
Frequently Asked Questions
What does the red master warning light mean on my SkyTrak 6034?
It signals a critical system failure, such as low oil pressure or overheating, and requires you to stop the engine immediately and check the display for fault codes.
Why is the check engine light on, and how can I clear it?
The check engine light on the SkyTrak 6034 indicates an emissions or engine fault; it can only be cleared after the issue is fixed and diagnostic trouble codes are reset by a dealer.
How do I reset the service hour meter reminder?
After performing the required maintenance on your SkyTrak 6034, press and hold the hour meter button for 5 seconds until the light turns off.
Can I drive with the amber master caution light on?
You can continue operating the SkyTrak 6034 with caution, but check the display message and address the warning promptly to prevent a more serious issue.
What should I do if the overload light flashes?
The overload light on the SkyTrak 6034 means the load exceeds capacity; lower the load immediately and redistribute or reduce weight to avoid tipping.
Is it safe to operate with the glow plug light on?
Yes, the glow plug light indicates preheating is occurring on the SkyTrak 6034; wait for it to go out before starting the engine, especially in cold weather.